HARDWIRED WATER RESISTANT SENSORS
 

Hardwired Water Resistant Sensors

GNT-IP67-HWS High Water Sensor, GNT-IP67-LVS Low Voltage Sensor 12 or 24 Volts DC, GNT-IP67-Snap Canvas Snap Sensor, GNT-IP67-DS2 Deck Pressure Sensors, GDC-EXT-NO Standard Wide Gap with Hidden Wire Extension Sensor, GNT-IP67-IBS Infrared Beam Sensor

hardwired-GNT-Pull-Sensor
GNT Pull Sensor

The GOST GNT Pull Sensor is a great sensor with multiple uses. Notification is given if the boat is pulled away from the dock, or the back of a yacht. It is also possible to install the sensors in several different ways. They can be installed with the female end on the dock or the mother ship, or they can have the male & female on the same vessel, which lends itself to more versatility. The sensor will cause the security system to go into alarm if the sensor is either pulled out or cut without first disarming the system. We designed this sensor to combat thieves coming up to vessels when they are tied up at night and cutting the lines and towing the vessel away with jet skis or other small watercraft which we have seen an increase in recent months.

GNT-IP67-HWS
GNT-HWS:

GNT-HWS : High Water Sensor

The GNT-HWS wireless High Water Sensor is designed to stand up to the harsh marine environment and includes a mounting bracket for the float switch that should be installed in the bilge of the vessel slightly below the vessels factory installed high water sensor.

GNT-IP67-LVS
GNT-LVS:

GNT-LVS : 12/24 - Low Voltage Sensor

The GNT-LVS wireless Low Voltage Sensor is designed to stand up to the harsh marine environment and is set to trigger an alarm when the voltage drops below 11.6v (on 12V Sensor) or 23.2v (on 24v sensor) for more than 2 minutes. This sensor will monitor any 12V or 24V battery bank. There is a dip switch on the circuit board that allows installers to switch the voltage monitored between 12 or 24 volts DC

snap-sensor
GNT-Snap:

GNT-Snap : Canvas Snap Sensor

The GNT-Snap wireless Canvas Snap Sensor is designed to stand up to the harsh marine environment and is set to trigger an alarm when the canvas cover is unsnapped. The canvas snap sensor is mounted in an existing snap location by drilling a 25/64” hole thru the vessel. The sensor is inserted in the drilled hole and secured with the brass nut on the underneath side. An O-ring under the snap base provides a seal to keep water from entering around the sensor head. This sensor is great for protecting vessels that are covered with a canvas cover. Because of its exceptional design, it is impossible to see, as the sensor looks like a normal snap when properly installed.

GNT-IP67-DS
GNT-DS2 or DS4 :

GNT-DS2 or DS4 : Deck Pressure Sensors

The GNT-DS2 or DS4 wireless Deck sensor is designed to protect the exterior or interior of the vessel. The sensors are epoxied to the underside of the vessel’s deck where they cannot be seen by intruders. In addition, they will not detract from the vessels decor. These sensors are effective on almost any boat structure including wood, fiberglass and even aluminum or steel decks. Environmentally sealed and utilizing 22-gauge marine grade wire leads, these sensors are ideal for those hard to protect areas of the vessel where there is access to the underside of the deck. They will not respond to vibration, shock, or airborne items. They sense only the unique flexing of the deck caused by a person walking. Sensitivity is fully adjustable from the processor. They can even be used to protect ladders up to the fly bridge or tuna tower.

Read more...

GDC-EXT-NO
GDC-EXT-NO :

GDC-EXT-NO : Standard Wide Gap Extension Sensor

Miniature Surface Mount, Wide Gap (white)
Hidden Wire (bottom)

GNT-IP67-IBS
GNT-IBS :

GNT-IBS : Infrared Beam Sensor

The GNT-IBS wireless infrared beam sensor is designed to protect the exterior of the vessel. There is an invisible infrared beam between the emitter and the detector (photoelectric eyes). Once the infrared beam is broken the sensor is activated and causes the system to go into alarm. These sensors are commonly installed in the gunwales to protect the cockpit areas. Other uses include open fly bridges to protect the electronics or any other exposed areas where a motion detector is not practical. These sensors have a built in fail safe amplifier and are resistant to sunlight and other interference. These sensors are also available with 2 sets of photoelectric eyes.